Positek

X120

Part no.: X120

Key Features

• ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)

• Sensor Mounting: M18 or 3/4" UNF threadTarget tube flanges available

• Available in any measurement angle from 0-5mm to 0-800mm

• Sealed to IP68 350bar, 3500msw, 5000psi(combined hydraulic and water pressure)

The 350bar X120 is an ATEX and IECEx approved version of the S120 cylinder sensor. The X120 is sealed for a maximum of 350bar combined hydraulic and water pressure. The unit is compact, space-efficient and responsive along almost its entire length.

Like all Positek sensors, the X120 provides a linear output proportional to displacement. Each sensor is supplied with the output calibrated to the travel required by the customer, our standard range covers any measurement range from 0-5mm to 0-800mm. As with all of our packaged sensors full EMC protection is built in.

The sensor is very robust, the body and target tube are made of 316 stainless steel for long service life and environmental resistance.

Overall performance, repeatability and stability are outstanding over a wide temperature range. The sensor is easy to install with M18 or 3/4″” UNF mounting thread options. The target tube can be supplied plain or with a variety of flanges.

This sensor is waterproof for submersion to 3500 meters (350bar combined water and hydraulic pressure).

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Approval only applies to the specified ambient temperature range and atmospheric conditions in the range 0.80 to 1.10 Bar, oxygen <=21%.
The 350bar X120 is an ATEX and IECEx approved version of the S120 cylinder sensor. The X120 is sealed for a maximum of 350bar combined hydraulic and water pressure. The unit is compact, space-efficient and responsive along almost its entire length.

Like all Positek sensors, the X120 provides a linear output proportional to displacement. Each sensor is supplied with the output calibrated to the travel required by the customer, our standard range covers any measurement range from 0-5mm to 0-800mm. As with all of our packaged sensors full EMC protection is built in.

The sensor is very robust, the body and target tube are made of 316 stainless steel for long service life and environmental resistance.

Overall performance, repeatability and stability are outstanding over a wide temperature range. The sensor is easy to install with M18 or 3/4″” UNF mounting thread options. The target tube can be supplied plain or with a variety of flanges.

This sensor is waterproof for submersion to 3500 meters (350bar combined water and hydraulic pressure).

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Approval only applies to the specified ambient temperature range and atmospheric conditions in the range 0.80 to 1.10 Bar, oxygen <=21%.

The 350bar X120 is an ATEX and IECEx approved version of the S120 cylinder sensor. The X120 is sealed for a maximum of 350bar combined hydraulic and water pressure. The unit is compact, space-efficient and responsive along almost its entire length.

Like all Positek sensors, the X120 provides a linear output proportional to displacement. Each sensor is supplied with the output calibrated to the travel required by the customer, our standard range covers any measurement range from 0-5mm to 0-800mm. As with all of our packaged sensors full EMC protection is built in.

The sensor is very robust, the body and target tube are made of 316 stainless steel for long service life and environmental resistance.

Overall performance, repeatability and stability are outstanding over a wide temperature range. The sensor is easy to install with M18 or 3/4″” UNF mounting thread options. The target tube can be supplied plain or with a variety of flanges.

This sensor is waterproof for submersion to 3500 meters (350bar combined water and hydraulic pressure).

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Approval only applies to the specified ambient temperature range and atmospheric conditions in the range 0.80 to 1.10 Bar, oxygen <=21%.

Call us for more info at 856-727-9500

  • Hi, My name is

  • and I’m interested in the

  • You can reach me by email at

  • or phone at

  • This field is for validation purposes and should be left unchanged.
You may also be interested in:

Positek

P103

  • Body Diameter: 35mm
  • Sensor Mounting: Flange or Body ClampsSpring loaded pushrod option available
  • Available in any measurement range from  0-2mm to 0-50mm (for 51-100mm range see P133)
  • Sealed to IP65/67 depending on connector/cable option

Positek

X112

  • ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
  • Sensor Mounting: 1/2" UNF ThreadSpring loaded plunger
  • Available in any measurement range from 0-5mm to 0-50mm
  • Sealed to IP67

Positek

E117

  • ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
  • Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available
  • Available in any measurement range from 0-5mm to 0-350mm
  • Sealed to IP67

Positek

Positek P505

  • 19mm diameter body
  • Analog voltage and current outputs
  • 0.25% linearity
  • Measure up to 160 deg range
Blog:

Torque Measurement with Angle Sensors

As collaborative robots expand into manufacturing environments the issue of safe motion continues to be a concern. Current design approaches involve adding force sensors, torque sensors, and sometimes proximity sensors. These adders along with more complex software control algorithms mitigate most of the concerns and result in slower operation. Unfortunately, these additional sensors also add significant cost and complexity.

Liquid Level Sensor Interface

The GS liquid level software is an excellent resource for people using sensors to measure fuel, chemicals, or even waste. One of the best features of the Gill Liquid Level Sensors is its compatibility with the GS Level software. The GS Level software makes it easy for the end-user or integrator to change the setting […]

Compact, Lightweight, Inductive Ring Encoders

IncOder™ CORE is a robust miniature PCB-based inductive ring encoder designed for robotic joints. IncOder CORE is a non-contact, lightweight absolute rotary inductive encoder fully contained in a printed circuit board kit. The ergonomic hollow bore design is suited for integration into rotary actuators. The position sensor utilizes a unique field-proven inductive technique, delivering highly repeatable, […]

VLP Product Line For Harsh Environments

Netzer Precision Position Sensors is pleased to introduce the VLP (Very Low Profile) line of absolute position rotary encoders for harsh environments. Designed for exposure to the extreme conditions that are prevalent in the Aerospace and Harsh Environment industries, the VLP-60 and VLP-100 encoders provide unparalleled performance while offering high levels of immunity to shocks, vibration, humidity, and extreme temperatures, and […]

Chips, Chips & Chips

What semiconductors, snacking and gambling all have in common: Encoders!

There has been a lot of talk lately around the global ‘chip’ shortage. Even social media last month was filled with cartoons of engineers asking Santa for semiconductors for Christmas. Rotary encoders such as the DS-130 by Netzer Precision are an important part of this ‘chip’ production. Accuracies exceeding 0.004 degrees, 21 bit resolution and a 90mm ID ensure that component placement can be done accurately and consistently.

Submersible Linear Sensors

Positek’s portfolio includes a range of high-accuracy linear sensors specifically designed for use in submersible applications. Made from marine grade stainless steel and offering the reliability that is not possible from a submersible LVDT or linear potentiometer, our sensors have served a host of different industries such as wastewater and offshore oil drilling. Another use […]

TECHNOLOGY LINEAR SENSORS

Many applications require linear motion to be monitored for system control or to ensure safety. With lengths ranging from 1 m to 30m (3’ to 98’), LINARIX linear sensors are available in many configurations to meet an application’s requirements. Options include a wide variety of outputs (including analog, fieldbus and Ethernet variants), heavy duty housings and compact design.

Academic Project

The University of Rochester Baja SAE Team using Opkon potentiometers donated by Everight Position to measure steering angle and suspension height. If your academic project looks like this: Awesome idea Enthusiastic classmates Cases of Red Bull and Mountain Dew Extremely limited financial budget Everight Position wants to help. We are actively looking for University Clubs […]

Redundant Encoder Options

While most modern rotary encoders rely on non-contact sensing technologies and have high MTBF specifications, in critical applications it is still common to have redundant sensors required. When selecting a solution, a number of different criteria need to be considered and fortunately different solutions exist, making the task less daunting. Redundancy One of the first […]

Netzer Electric Encoder Explorer Software

Get started with Netzer Electric Encoder Explorer Ready to learn how to get started with Netzer Electric Encoder Explorer? We can help!  Take a look at this video where we walk you through the software and teach you the ins and outs of the Netzer Electric Encoder Explorer.  Start with Signal Amplitude One of the […]